高速瓦楞纸板生产线
SF-320吸附式单面机
SF-320 FINGERLESS SINGLE FACER
1、 结构特点:
(1)采用真空吸附式导纸,配备高压强力风机。设有风量调节装置机吸风消音装置;电气控制集中于同一电柜距离主机不小于1.5米,操作侧全封闭侧罩。
Apply the vacuum adsorption leading paper, equipped with high-pressure powerful fan. Equipped with air conditioning machine air suction device; and censored The electrical control focused on the same electric ark distance not less than 1.5 meters, host operating side closed side cover.
(2)万向节传动,分体结构独立驱动箱。封闭式齿轮传动寖油润滑,可延长齿轮的使用寿命。
Gimbal transmission, the body structure independent driver box. Enclosed gear transmission oil lubrication, can prolong the service life of gear.
(3)涂胶辊和定胶辊设计为成组导轨滑移,拆装方便快捷。
Glue roller and rubber roller is designed to block guide rail sliding, tear open outfit is convenient and quick.
(4)机座及墙板铸铁结构,墙板厚度为180mm。
Base and wallboard cast iron structure, wallboard thickness for 180mm.
(5)瓦楞辊采用48CrMo**合金钢,经调质、淬火、表面磨光,瓦楞辊直径Ø320mm,表面硬度为HRC60度以上;瓦楞辊采用气缸控制上下位移。
Corrugated roller adopts 48CrMo high quality alloy steel, via piece.modified, quenching, surface polishing, corrugated roller diameter Ø 320mm, surface hardness for HRC56-60 degrees, Corrugated roller adopt air cylinder pressure.
(6)压力辊直径Ø320mm,表面消磨加工并镀铬处理;气缸控制上下位移,材质为中碳钢45号、调制处理。
Pressure roller diameter Ø320mm, surface treatment processing and kill chromium plating, Cylinder controlled fluctuation, material for medium-carbon steel displacement 45, modulation handle.
(7)预热辊直径Ø400mm,表面消磨加工并镀硬铬处理,全部用金属软管连接。
Pre-heater roller diameter Ø 400mm, surface treatment processing and hard chromium plating. All connecting by flexible
metel tube.
(8)瓦楞辊与压力辊轴承采用耐高温润滑脂润滑轴承。
Flute roller and pressure roller bearings use high-temperature grease lubricated bearing.
(9)气动控制给胶退胶,涂胶辊直径Ø245mm,表面磨光后刻有凹坑式网纹 镀硬铬处理,调胶辊表面消磨加工并镀硬铬处理。
Pneumatic control to glue back glue, glue roller diameter Ø 215mm, surface polishing after engraved with hard chromium plating pit type anilox roll surface treatment, adjustable glue hard chromium plating kill processing and handling.
(10)采用电动隔浆装置,涂糊部在主机停止时仍可独立运转,防止浆糊干涸。
Adopt electric plasma device, coating the paste on the host to stop when the independent operation, to prevent the paste to dry up.
(11)瓦楞辊单边中高0.10mm,压力辊单边中高0.075mm。加限位装置,压紧气缸为Ø160 mm气缸。
Corrugated roller unilateral high 0.10 mm, pressure roller unilateral 0.075 mm high. Add peneumatied device, pressure cylinder for Ø 1.6 mm cylinder
2、 技术参数:
(1)工作幅宽 working width:1800mm。
(2)设计速度:120米/分。(实际经济速度以加热方式及配置而决定)
Design speed:120m/min.(The actual economic speed based on the heating mode and configuration)
(3)操作方向:左手机或右手机(需根据客户厂房确定)。
Operation direction: left or right (need according to customer"s plant sure).
(4)气源:0.4—0.9Mpa。
Source: 0.4-0.9 Mpa.
(5)油加热,较佳使用温度在实际操作后确定,锅炉要求流量10立方/小时,要求提供热量10万大卡/小时,进出油管径1.5寸
Oil heating, the best temperature should be determined with the actual operation, boiler requires 10 cubic meters/hour, and provide a 100000 calories per hour, input and output pipe diameter 1.5 inch
(6)瓦楞楞型:楞高0.7mm,楞**直径0.62mm,楞沟直径0.88mm,周节(楞**间距)3.1mm
Flutes shape: Flute height 0.7mm, diameter of flute peak 0.62mm, flute bottom 0.88mm, interspace 3.0mm
(7)收缩率跳动600mm长度±1mm
percentage of contraction 600mm, length ±1mm
3、辊类直径参数:
Roller class diameter parameters:
(1)瓦楞辊直径:Ø320mm
Corrugated roller diameter Ø320 mm。
(2)压力辊直径:Ø320mm
pressure roller diameter: Ø 320 mm.
(3)涂胶辊直径:Ø245mm。
Glue-coating roller diameter: Ø 245 mm.
(4)预热辊直径:后Ø400 mm。
Preheat roller diameter: Ø 400 mm.
4、 动力电机参数:Dynamic motor parameters:
① 主电机:11KW 380V 50HZ
The main motor 11KW 380V 50HZ
② 吸风电机:15KW 380V 50HZ
Air suction motor 15 KW 380V 50HZ
液压纸架
Hydraulic Mill Roll stand
1、 结构特点:Features:
(1)结构对称可同时支持两卷原纸,可不停机换纸作业;原纸夹紧、升降、松开、移动对中、左右平移均采用液压控制。
Symmetrical structure, can load two raw paper at same time, Raw paper changing without stop, the clamping, loosening, lifting up and down, moving left and right adopt hydraulic control
(2)有效工作宽度:1800mm。
Effective work width: 1800mm
(3)较大原纸:Ø1800mm×1200mm。
Max. Raw paper: Ø1800mm×1200mm。
(4)较小原纸:Ø400mm×400mm。
Min. Raw paper: Ø1800mm×1200mm。
(5)单臂较大负重:3000Kg 。
Loading capability of single arm: 3000Kg
(6)每台无轴支架配有送纸导轨两条,上纸小车两台;导轨采用12号槽钢与导向柱焊接,上纸小车采用12mm钢板焊制,送纸导轨长为4500mm。
Each mill roll stand has two ground rail and two paper carriages; The main frame of rail is 16# channel steel welded; paper carriages use the 12mm thickness steel board weld, total length 4500mm
(7)多点式气动刹车。
Multi-points pneumatic breaks.
(8)自动双膨胀式卡头
Automatic dural expansion finials.
(9)电器元件集中控制,可大大提高生产效率。
All the electric appliance are installed on one control board, improve the production efficiency.
2、 技术参数:Parameter
(1)原纸架动作方式:液压式操作
Operation methods: Hydraulic type
(2)夹纸范围:较大:1800mm 较小:400mm。
Clamping range: Max.1800mm Min 400mm
(3)夹纸直径:较大:1400mm 较小:400mm。
Dia.of raw paper: Max.1400mm Min 400mm
(4)单侧较大负重:较大3000Kg。
Loading capability of single arm: 3000Kg
上纸小车、导轨
ground rail and two paper carriages
(1)上纸小车装有导向轮,可平稳的将原纸推送到位。
The carriages with guiding wheels, can push the raw paper to the specified location
(2)导轨整体埋地,导轨主架由12号槽钢和Ø12冷拔钢焊制而成,导轨长度为4500mm。
The rail are buried in the ground, the frame of rail is made from 12# channel steel and Ø12 cooled drawn steel, length of rail: 4500mm
(3)每台支架配有2条导轨和2台上纸小车,可从支架两侧同时上纸。
Each mill roll stand has two ground rail and two paper carriages; can load raw paper at the same time
(4) 主要外购件、原材料及产地:
Main parts, materials and origin
主要件名称 Name
**或产地 Brand or Origin
材质 Materials
导轨及上纸小车Rail and carriage
唐山钢材厂Tangshan Steel
轴承 Bearings
哈 瓦 洛 HRB,WFD,LUO
预热器
Pre heater
产品特性:
Features:
1. M型为面纸预热器,X为芯纸预热器,D型为多重预热器。
M model surface paper pre heater, X model core paper pre heater,D model multi ply paper pre heater,
2. 预热辊体动平衡试验,辊体表面精密磨削。
Preheating roller get dynamic balance adjusted, surface with precision grinding and hard chromium plating processing.
3. 预热辊分固定式或旋转式,转动式装有制动装置,随时调节纸张张力。
Fixed type and rotary type can be chosen, the rotary type has break device, can adjust the tension of paper at any time.
4. 电动调整预热面积,0~220°范围内任意调节。
Electric adjust the heating area, 0~220°arbitrary regulation.
5. 忒纸预热安装有喷雾装置,可随时调整纸张的干湿,利于瓦楞成型。
The core paper pre heater adopt spray device, used to adjust the paper dry or wet condition, conducive to corrugating moldin6. 预热辊直径φ800mm
Diameter of pre heater: φ800mm
输纸提升过桥
Conveying and lifting bridge
过桥提升传动为独立电机提升,与单面机同步,输纸过桥将单面机所出的纸板通过输送带直接传到横切机的
规格 : 380 ;
售后服务 : 整机一年保修 ;
包装类型 : 箱 ;
适用对象 : 果汁饮料,药水,化妆品类,矿泉水、纯净水,碳酸饮料,酒类饮料 ;
用途 : 生产纸板 ;
类型 : 瓦楞纸板生产线 ;
产品别名 : 单瓦线 ;
型号 : 380型单瓦线 ;
** : 精峰 ;
加工定制 : 否 ;